Allows A2/L1/L2/Kroma series threaded switch flashlights to “tailstand” for “candle mode” operation and be used with a handgun.
For more information on which tailcaps this will work on, see this thread at CPF.
(sorry for crappy iphone pics)
NEW PRICING STRUCTURE:
QTY 1-5 = $17.00 delivered CONUS (USE BUTTON BELOW)
QTY 6-10 = $12.00 delivered CONUS (EMAIL ME for invoice and ETA)
USE BUTTON BELOW TO ORDER ITEM |
INTERNATIONAL ORDERSAdd button below ONCE per total order to cover Global Flat Rate Envelope cost of $12.40 |
| secured by https://paypal.com. | |
The A2/L1/L2/Kroma Tail Shroud turns the tail-switch into a tail-standing unit. The “tactical” version is ~1.20” in diameter (body of light is .900") to allow it to be used with a handgun in the “Rogers” or Graham” methods. These were designed to maintain a good seal on the rubber boot, and should have no negative impact on water resistance. Modification of the original switch is required to put this shroud on, which will likely void the warranty. To install, remove the stock retaining ring from the back of the switch by turning it counterclockwise, and replace with the shroud unit. The stock unit may be held secure with a form of Loctite, and may require heat to break free. I recommend using a hairdryer for a few minutes to remove.
Allows A2/L1/L2/Kroma series threaded switch flashlights to “tailstand” for “candle mode” operation.
For more information on which tailcaps this will work on, see this thread at CPF.
NEW PRICING STRUCTURE:
QTY 1-5 = $15.00 delivered CONUS (USE BUTTON BELOW)
QTY 6-10 = $12.00 delivered CONUS (EMAIL ME for invoice and ETA)
QTY 10+ = $10.00 delivered CONUS (GROUP BUYS, not resellers! - EMAIL ME with GB link for invoice and ETA)
USE BUTTON BELOW TO ORDER ITEM |
INTERNATIONAL ORDERSAdd button below ONCE per total order to cover Global Flat Rate Envelope cost of $12.40 |
| secured by https://paypal.com. | |
The A2/L1/L2/Kroma Tail Shroud turns the tailswitch into a tailstanding unit on. The straight version is the same diameter as the body to allow it to fit into holsters. These were designed to maintain a good seal on the rubber boot, and should have no negative impact on water resistance. Modification of the origional switch is required to put this shroud on, which will likely void the warantee. To install, remove the stock retaining ring from the back of the switch by turning it counterclockwise, and replace with the shroud unit. The stock unit may be held secure with a form of Loctite, and may require heat to break free. I recommend using a hairdryer for a few minutes to remove.
This is two items that I made to make the SureFire G2 a little more user friendly when using it with a handgun in the “Graham Method” of holding the light while shooting. They are made from Delrin (super high tensile strength plastic) and come in black only.
$10.00 Delivered
USE BUTTON BELOW TO ORDER ITEM |
INTERNATIONAL ORDERSAdd button below ONCE per total order to cover Global Flat Rate Envelope cost of $12.40 |
| secured by https://paypal.com. | |
I find his method much easier than the “Rogers,” because it does not compromise my grip and still keeps the light parallel with the barrel. Unfortunately the G2 has a tail switch that is a little too small and short to take full advantage of this method so I made this modification to change that.
Both parts slip on and do not permanently modify your flashlight. You will loose some water proofing since the rubber cover is no longer used, but the diameter of the extension is .525” and fits into the .530” hole on the tailcap with a good seal.
My bet is that you will have the same level of water resistance as before, but buyer beware I don’t guarantee it.
Unassembled pieces…
Button extension on factory part…
End view…
Light activation and grip…
Illustrating operation contact point…
Full contact with support hand palm is allowed with this method. I can use my normal IPSC thumbs forward grip with this method…
Front view…