Oregon Shooter

I want to do this so I have documentation, of what has been
done, and how it worked. I don’t care about 500rds without a FTE, or
FTF. Once it was buried in the mud w/a full mag, and when I dug it out
the next day it went bang the first time I pulled the trigger but the
weight of all the mud on the slide kept it from cycling. I scraped off
most of the mud on my boot and fired the remaining 12 shots without a
problem.

I want to know how much can it take and still function. If not function perfectly – what will it take to get running again.

Its
all been done already, I’m just going to keep track this time. Heres a
pic after around 15K rounds with no cleaning, and being buried in mud
etc...
The barrel fouling was amazing, it was basically a smooth bore.

Play Sand
Potting Soil
Baby Powder
1 bucket of water for cleaning
2 buckets for mixing ingredients.

This
entire process took place over 45 minutes. The pistol was never field
stripped, and the only cleaning was dunking in a bucket of dirty water.

Sand
Boring, but gotta do it. Used play sand, good consistency.

Need a little pressure so 10lb sledge was used to slightly pack it in place.

shot after buried, loaded, closed slide
video coming soon

shot after buried, loaded, slide open
video coming soon

Potting soil, a good mix various dirt and junk.

slide open

shot after buried, loaded, closed slide
video coming soon

shot after buried, loaded, slide open
video coming soon

Baby Powder, fine enough to get into everything.

slide open

shot after buried, loaded, closed slide
video coming soon

shot after buried, loaded, slide open
video coming soon

Mud (potting soil and water)
Nice sticky mess

remember this is from one test to another, it now has sand, dirt, and powder in it.

shot after buried, loaded, closed slide - started to get messy.
video coming soon

shot after buried, loaded, slide open
video coming soon

Rinse time

Paste – Baby powder and water. Stupid idea.

shot after paste, didn’t even try it with the slide open.
video coming soon

Needs a rinse and mag through to help dry. The mag was empty before the water quit pouring out!
video coming soon

Lets dump everything into one bucket and mix it together.

That’s about the limit
video coming soon

The mag is full of crud, the trigger must be pulling at 20lbs, time to rinse again and see field strip.
I wonder if the stone wedged in the transfer bar had anything to do with the heavy trigger?

For overnight, it will soak outside in a the rinse water mixed with a dose of rock salt.

good night

I
used 1 target for the test, paced 35’ feet away. Not bad considering
half the time I couldn’t see the sights. The increased weight of the
trigger must have had me pulling to the right.
Need to take more
than 1 magazine next time. There were a few times the mag was so full
of stuff I only only fit 10 or 11 rounds. I think some of the FTF were
partially the mag.

Not
sure whats next. The large amount of rock salt kept it from freezing
out side last night. What would be the best condition for corrosion?
Should I leave it outside or bring it in and let it soak? Hos long? The
“camera man” from the other pics is convinced the salt will turn the
barrel into a rusted mess. We’ll see how good the tennifer is.

As
a side note - a friend who is a pilot has agreed to take me up this
spring and let me throw it out the window of his plane! We’ll decide on
the height later, but the slowest he said he can go is 65mph.

I’m thinking my next plan will be to start breaking parts myself.
Will if function if the spring cups are shattered?
How much if the striker spring can be cut and still work.
Will it run without an ejector?
I’m still stoked about shooting it without the trigger spring!

I dont care so much about it working, I want to find what makes it stop and how to keep going.

Took
the glock out of the salt water, and ran 500rds through it. Sorry,
would have done 1K, but this was PAINFUL. No cleaning or oil, since the
last tests.

I learned I have an aimed rate of fire of 100RPM
Attempted
to load several mags at once and blast through one at a time. After the
3rd mag my hand was almost numb, and I had to really hor at holding on.
Need to shoot 2 mags rest a couple minutes and shoot 2 more.

Time to stick my hand in a bag of ice.[XX(] Not the smartest thing I’ve done....

Salt
water is nasty. Looks like all the tennifer pieces are fine, but
untreated parts didnt stand a chance. I believe the rust on the barrel
dripped down from the guide rod and should wipe right off.

Its
just discolored, everything slides, clicks, and sproings just fine. I’m
going to clean everything and see what is actually rust and what is
just “runoff”.

I’ll keep those springs until they break[:D]

Good
as new, almost. The Guide rod has pitting dammage, and so does the
slide lock but thats the only evidence remaining. The locking block
must have tennifer along with all the pins. The sopts on the bottom of
the barrel discolored the finish, but the metal is still glass smooth.
The other parts must be stainless steel, as it rubbed off, but didnt
wipre righ off like the barrel and slide.

I
finally got a chance to see how it did with bead blasting media. If you
have never felt this stuff, its really cool, so small and round, it
feels almost like water. Here’s a pic of the media used midex with
common table salt and a dime

I
put a few cups in a baggie with the pistol and shook it up good, took
it out and shot the rounds I had in the mag. I repeated this three
times. The video sucks, as I had to set it up to record by myself.

Bead Media Test

First
time no problem, except I got a beads all over my face, so I let it run
out a bit on the second. The second time a round failed to feed because
the magazine was binding up. The third time, was worthless because I
had gotten enough media in the mag to make it useless. The weak spot
here was the magazine, the media got in there and had no where to go. A
new magazine and I’m sure it would work fine. Not a flawless test, but
I cant find the line until I cross it. Again, nothing that a simple
field strip and shaking out couldnt fix and back into action.
After
I shook it out, I put a handful of play sand in the bag and shook it
up. Same old results from every other time it was full of sand. It
worked just fine. 

Just a .22 pistol 30’ away. I
didnt expect it to do any damage, if we hit where we were aiming. Hit
it 10 times before I lost my nerve and didnt want to risk hitting the
frame. One hit the extractor, but didnt hurt anything.

I took some degreaser and steel wool to one of the spots. It basicaly rubs right off.

Its been boiled before , no ill effect.

ever wonder what the magwell looks like after inserting hundreds of muddy magazines, and forcing mags into a muddy frame?

Over
time the transfer bar and disconnect have worn grooves into each other.
I guess that will happen what contacting metal parts are never oiled.
This may be the reason for the 8.5lb trigger?

And for those who say the plastic mag catch will wear out..... nope, they built it plenty strong too.

A
customer came to me last week with his USP .45 Compact he had just
gotten it back from HK who had replaced a broken trigger bar. It has
fewer than 1K rounds through it, and is well taken care of. He asked me
if I would trust a pistol that broke, and was fixed by the factory. I
said no. He asked me to run 500rds through it and see what happened.

I took his pistol and 8 magazines, My 21 and 8 magazines, and 1K rounds of ammo.
Both pistols were field stripped and blown completely clean and dry with compressed air.
2 mags were emptied in clean condition to make sure everything was fine.

For the fist comparison I threw a couple handfuls of play sand in a bucket.

I
took each pistol, full mag, round in the chamber and shook it in the
sand for a few seconds. I did this first with the 21 and it went bang
13 times as expected.

I pulled the USP compact out of the
bucket(it was loaded but decocked), pulled the trigger, hammer falls
but no bang. I pull the trigger again and still no bang. Not a squib,
and not a delay. I cycle the slide and eject the cartridge, but it
fails to go into battery. I repeat, while shaking out sand, until the
magazine is empty. After removing the slide blowing the frame out with
compressed air I repeat the test.

wont lock

Back in the
bucket, shake, attempt to shoot – exact same results. Field strip and
blow out with compressed air. This was attempted 4 times, with 4
different magazines. The first shot did go off once, but did not lock
up for the following round. Again it required fieldstripping to
function.

OK,
it doesn’t work in sand. For a different twist, I took a UPS mag and a
glock mag and threw them in the bucket and shook them up.

I
picked up the 21 mag, loaded the pistol, pulled the trigger 13 times. I
then picked up the USP mag, pulled the trigger once and it went bang.
The slide failed to close on the second round. Ejecting the 2nd round
partially inserted the 3rd but also a bunch of sand. The USP mags have
basically a shovel extending for the slide stop, which proved them
useless combined with the sand.

Sand is over, time
for good old potting soil. Potting soil was basically a repeat of the
sand. The USP never went bang once. Even with a round in the chamber,
and numerous hammer strikes, nothing.

hammer video

Cycling by hand ejected round, but would not lock up on the following round.

After that we gave up, on the USP and took turns emptying the several full 21 mags.

I’ll
return the customers pistol and his 500 rounds. This USP compact went
bang every time clean, so it works fine. I would never trust it though,
as a carry piece. 

I wanted to try another salt water
test on the slide and barrel. I mixed up a good mixture of road salt
and water, and poured it into a glass of water. I then took a sock I
had been using as a rag, and put the slide and barrel in the sock. I
then put the sock into the salt water glass. I know it needs air to
rust so I poured out the access water, and set the glass on the outside
windowsill where it was exposed.
Well, the sock is now dry. Will
leaving it sit for a few more days accomplish anything more or has this
test gone as far as it can go?

After 1 week there the rust is seeping through the once black wool sock.

I
think its just runnoff rust from the sights. Its supposed to be raining
for the next day here, so I’ll set it on my back deck to rinse off
overnight.

Time for some WD40 and a brillo pad

I
learned how deep the tennifer goes. corners of the slide where it had
been dropped/dinged/gouged were full of honest to goodness rust. The
brillo also seemed to tak off most all of the black finish for the
first time too!. I guess the concentrated salt water in the sock was
the last straw for it. Other than the damaged areas, nothing rusted, so
I’l sure under normal use it would have been just fin under the same
conditions.

Preparation
for one more test. X marks the spot. 500’ at 100PMH. Will take place as
soon as can be coordinated between plane, pilot, and spotter on the
ground.

I’m
still waiting for the corn to come down for the plane toss, but I
wanted to think of something I haven’t done yet. I never put it up
against a pick up truck?

Speedbump?

Dirt speed bump?

Need to shake the dirt loose form the barrel, so I tied it to the bumper

Run through what mags I have loaded.

May as well shake it out with one more road trip. The mag was always full, but no round in the chamber for the “draggings”.

The rear sight took a bump to the right.

couple wacks with hammer should get it back on paper.
sight adjustment video coming soon

Looks good, lets see how it hits at 35’. (sorry for the focus was zooming in on the target)
Accuracy Video coming soon

results

A
bit to the left, but good enough. Even after all its been, it still
groups as good as it did the day I got it, well at least as well as I
can shoot it!

I wondered how it shoots at 50yds with S&B ball ammo, and the filthy crunchy, heavy trigger?

First
13shot group was to the left, so I gave it another wack with the
hammer. The second 13shot group was the bad guy. Good enough for a
fighting .45!

I’m really running out of ideas, so decided to drop it off the roof with a primed case in the chamber to see if it would go off.
Primed brass in the chamber, and a full mag for weight in the pistol.

No
surprise, it didnt go off. The surprise/scare was when I went to shoot
it. the first 3 shots went off fine. The 4th failed to lock into
battery, so I had to wack it closed. 5th shot went off fine, but 6th
failed to go into battery. I wacked it but it was stuck. I went and got
the hammer and pounded the slide back and locked it open. Everything
looks ok? I put the mag back in and close the slide on the next round.
Works fine, goes bang. The following shot locked the frame out of
battery again with the round half way in the chamber. I opent it up
with the hammer again and field strip it to see what wrong. Trigger bar
bent? frame bent? I’m sitting on the ground and pick up one of the
rounds that was stuck and drop it inthe chamber - it wont fit. WTF? I
putt it out and its flat on one side. Bullet case and all. I grap the
others and they are the same. I guess it fell hard enough to smash all
the rounds staggered on that side of the magazine.

Oh well, it still works.

Just
a reminder, this isnt a “test” only pistol. This is my usualy IDPA, 3
Gun, Carbine class pistol, and it does not get cleaned/lubed before use.

I used it in a 3 Gun match on Saturday, and as usual, it worked like a clock.

It gets normal use. I need the 13rd capacity when shooting at poppers set for 00 buck, that will only go down with head shots.
shot gun poppers

It took me 20 minutes to find it stuck in the dirt, so its only fair for you wait [:D]

All that was visible, was the bottom of the magazinem and about 2” of grip, the rest was under ground.

Here’s what the point of impact looked like.

So what do you think it will look like when I pull it out of the ground?

There was dirt in everything. When I took it out of the dirt the slide stuck back about 1”.
I
had shook most of it out by the time we had walked back to the yard. It
shot and functioned fine, didnt even have to field strip.

Still very much minute of dead. Not bad considering what its been through and not having any cleaning or lube since page 12. 

It shoots just as well as I have ever been able to shoot it. I can easily hold a fist size group at 30’, which all I need.

Heres a 25’ 10 shot group immediately after it was dropped from the plane, with the trigger still full of dirt.